Simply turn the socket in the opposite direction and the build should pull out. The upper 10mm bolt is covered by a wire loom and power connector attached to it. There are two hex head bolts that hold the tail light assembly in place. It will stay on for a few secs. This article has also been viewed 52,668 times.
Nissan Tilda outside North America is fairly simple, here's the guide to do it your self. If necessary apply a little pressure on the interior screw posts. From the outside, pull the lamp assembly backwards. Remove the top and bottom 10mm bolts with a ratchet. There aren't seem to be a lot of picture tutorial on how to remove the headlight on the web, I decided to write my own detail picture tutorial and share it with you guy.
But when i want pull and uninstall. Use a 10mm wrench to loosen, then remove by hand. It seems like just replacing the taillight could damage those. Fast Shipping Guaranteed Most orders are shipped out the same day as they're received. Now you can turn the bulb socket a quarter turn remove the bulb. . Also don't mind the grammar as English is my second language.
With a little hand force don't use a screwdriver, it may crack the light or scratch the paint you should be able to pop the light assembly … out. Then gently pry out the two plastic access panels with the flathead screwdriver and set them aside in a safe place. With force going directly back it eventually gave in and loosened. Be careful not to damage the white nub as it helds the headlight in position This is what it look like when you remove the headlight Replace the light bulb by twist it counter clockwise. Line up the threaded bolt ends and metal spikes on the back of the tail light housing with the holes in the rear corner of the vehicle's metal body panels. Note: I am not a registered charity.
Now put it back together. After spending several hours on different web sites I found Go-Parts. Now turn the key on and watch the light. This video demonstrates how to change a burnt out taillight bulb on your 2009 Nissan Versa. Replacement bulbs with their part numbers are as follows: Brake Stop , Reverse Back Up and Rear Turn Signal. If you have magnetic sockets, this would be a great time to use one.
I guess that doesn't sound so bad but it doesn't slide out that easy or slides back in. Carefully push the tail light on to the rear of the vehicle. The upper 10mm bolt is covered by a wire loom and power connector attached to it. Once both of the 10mm nuts have been removed, you can gently pull off the tail light assembly from the rear corner of the vehicle. I couldn't have done it without them! Just pull and turn the light assembly and it will come off. The light grey reverse light bulb socket is located at the edge of the housing closest to the center line of the vehicle.
The wires connecting to the highlight are short and you might damage it if you yank it out too hard. Push the plastic pins back into the holes first, then the bolt side. Line up the threaded bolt ends and metal spikes on the back of the tail light housing with the holes in the rear corner of the vehicle's metal body panels. The housing on my lights is more of a triangle, with sharp points at the bottom rear and top side of the car, and the stud catch in the center of the triangle at the third point at the bottom side of car. The fender side of the taillight is snapped on. Tools you are going to need: 2 short flat rope or thick string paper towels flat head screw driver wrench First locate the 2 covers Pry it open using the flat head screw driver. It has obviously not been packed properly for shipment.
Once both nuts are removed, proceed to the outside of the taillight assembly and gently insert a flat head screwdriver between the taillight and vehicles body, starting at the bottom of the Taillight. But when i want pull and uninstall. Note on the exterior there is a slot at the front of the lamp assembly when reinstalling. Donations are not tax deductible. I couldn't have done it without them! Since the tailights are on whenever your parking lights or headlights are on, they will burn out eventually. Nissan has holes in the body to access the tail light bulbs that may make the bulbs too difficult to remove without removing the whole tail light.
Put the cover back in once you're done. Slightly loosen the lower 10mm nut with the socket and ratcheting wrench. I guess that doesn't sound so bad but it doesn't slide out that easy or slides back in. Since some of you guys here are new owners I thought I'd save you a trip to the dealer once you start modifing your armada's. When you need to replace the headlight, turning signal or parking light bulb on your 2009 Nissan Versa, finding out what the replacement size you need can be a time consuming task. Citations can be issued for products that do not meet the minimum regulatory requirements. These are the best instructions I've found for replacing the Nissan Versa sedan tail light.
I'm not sure what set's it off othe … r than pulling things apart but at some point you will likely end up with a flashing airbag sensor light. You can watch this for a little while, no hurry. Tighten the nuts with the socket and ratcheting wrench. No one locally had the part because the vehicle was too new, and the online stores had a somewhat high mark-up on their parts. I suggest 2 people work toward getting the lens off the drivers side.